How to Reset Whirlpool Cabrio Washer

A comprehensive step-by-step guide on how to reset Whirlpool Cabrio washer between cycles and at the end of the wash.

This article provides tips and tricks to help you maintain your washer’s optimal performance.

Step 1: Verify the Washer is Not in Use

Before attempting to get water out of your Whirlpool Cabrio washer, ensure that the washer is not in use. If the washer is still running, wait until the cycle is complete and the washer is powered off before proceeding.

Step 2: Locate the Drain Pump and Discharge Hose

The first step to getting water out of your Whirlpool Cabrio washer is to locate the drain pump and discharge hose. These components work together to remove water from the washtub between cycles and at the end of the wash. The drain pump is typically located at the bottom of the washer, while the discharge hose is connected to the drain pump and extends to the plumbing system.

Step 3: Remove Obstructions from the Drain Pump

If the washer fails to drain, the lid can be opened, and any obstructions in the drain pump can be removed.

This may include small items of clothing, lint, or other debris that may have become trapped in the drain pump.

To remove obstructions, disconnect the power and unplug the washer, then remove the access panel to access the drain pump.

Once you have access to the drain pump, remove any obstructions and reassemble the washer.

Step 4: Check the Discharge Hose for Kinks

If the washer is still not draining, check the discharge hose for kinks or obstructions. The discharge hose should be free from any kinks or bends that may restrict the flow of water.

Related: How to Change Keurig Water Filter

If the discharge hose is kinked, straighten it out, and remove any obstructions. Once the hose is free from obstructions, reattach it to the drain pump and the plumbing system.

Step 5: Check the Water Inlet Valve

If your Whirlpool Cabrio washer is not filling with water, it may be due to a faulty water inlet valve.

To check the water inlet valve, first, disconnect the power and unplug the washer. Then, remove the water inlet valve by pulling off the two wires on the valve’s terminals and unscrewing the mounting screw to remove the valve.

Once the valve is removed, squeeze the hose clamp on the inlet valve, and slide the hose off the valve. Check the valve for any debris or obstructions, and replace it if necessary.

Step 6: Verify Water Supply and Pressure

If the water inlet valve is functioning correctly, the next step is to verify the water supply and pressure.

Start by checking the tap and verifying that the water supply to the washing machine is on. If the supply is off, your washer won’t get any water.

If your Whirlpool Cabrio washer is getting water supply, make sure that the water pressure is not low.

If the flow is not strong enough, the water won’t travel to your washer, leading to issues with filling the washer.

If you have already checked the drain pump and discharge hose, and they are not the cause of the problem, there are a few other potential causes to consider.

For example, a malfunctioning timer or burnt heater can cause the washer to not drain or fill with water. It is best to consult a service technician if you suspect these issues.

To fix a clogged drain pump, you can remove the hose at the inlet side of the pump and check for debris in the filter.

Clear any debris away and reattach the hose to the inlet side of the pump. If you suspect the water inlet valve is the issue, pull off the two wires on the valve’s terminals, and unscrew the mounting screw to remove the valve.

Related: Does Gas Stain Asphalt

Squeeze the hose clamp on the inlet valve, and slide the hose off the valve.

In summary, if you want to ensure that your Whirlpool Cabrio washer is functioning properly, it is crucial to maintain and clean its drain pump and discharge hose, check the water inlet valve, and confirm the water supply and pressure are sufficient.

By following these steps, you can avoid common issues such as your washer not filling with water or not draining properly, and keep your machine running smoothly.

Reset Whirlpool Washer Front Load

There are a couple of different ways to reset a Whirlpool front-load washer. The first and most popular technique is to unplug the washer for at least two minutes, then plug it back in and wait for around 30 seconds before restarting the washer.

The machine will restart if you reconnect it after performing a hard reset with this.

Utilizing the control panel’s “Restore Factory” option is an additional strategy. By choosing this, all of the machine’s settings will be restored to their factory defaults.

It is crucial to remember that after utilizing this setting, you must reset the clock and re-establish WiFi connectivity.

Thirdly, disconnect the washer for one minute, then plug it back in while swiftly lifting and lowering the lid/top six times in 12 seconds.

Because different Whirlpool washer models may have different reset procedures, it is advised to consult the washer’s manual or get in touch with Whirlpool customer support for detailed instructions.

How do You do a Hard Reset on a Whirlpool Washer?

There are several ways to perform a hard reset on a Whirlpool washer. One approach is to disconnect the washer for at least two minutes, then plug it back in and wait around 30 seconds before restarting it.

Another method is to turn off the washer, select the “normal” setting on the mode dial, then rotate the dial counterclockwise one click to the left, clockwise for three clicks, counterclockwise for one click, then clockwise with one click.

The washer can also be reset by simultaneously pushing two of the pause/cancel and one of the power buttons.

Related: Why Does Car Oil Burn and How to Address It

The dial, opening and closing the lid, and resetting the circuit breaker are further techniques.

For detailed instructions on how to conduct a hard reset on a Whirlpool washer, it is advised to check the user handbook.

Conclusion

Getting water out of your Whirlpool Cabrio washer requires a drain pump and a discharge hose to remove the water from the washtub between cycles and at the end of the wash.

If your washer is failing to drain, you can check the drain pump for obstructions or the discharge hose for kinks.

Additionally, if your washer is not filling with water, you can check the water inlet valve and verify the water supply is on.

If the supply is on but the flow is not strong enough, the water won’t travel to your washer, leading to the washer not filling with water. To fix this, ensure that the water pressure is not low.


FAQs:

Why won’t my Whirlpool washer start but clicks?

If your Whirlpool washer clicks but does not start, there may be a problem with the door or lid switch.

This switch is designed to prevent the washer from starting if the door or lid is open. If the switch is faulty or not engaged properly, the washer will not start.

You may need to replace the switch to fix the issue.

What is the LD code on a Whirlpool Cabrio washer?

The LD code on a Whirlpool Cabrio washer indicates a “long drain” error. This means that the washer is taking too long to drain the water from the tub.

This could be caused by a clogged drain hose or pump filter, a kinked drain hose, or a faulty drain pump.

Try cleaning the drain hose and pump filter, straightening any kinks in the hose, and checking the drain pump for any signs of damage.


Video:

In this video, SVC Repair Solutions provides step-by-step instructions on how to disassemble a Whirlpool Cabrio washer.

The video covers the tools required for disassembly, how to remove the control panel, how to disconnect the lid switch and wiring harness, how to remove the cabinet, and more.

This video is a great resource for anyone looking to disassemble their Whirlpool Cabrio washer for repair or maintenance.